Search results

The Pro filer Tunnel Ram,..........is that for the 12 deg or 24 deg heads.......?????????

Never mounted in trailer, been collecting dust for awhile. Comes with used winch. $1,800.00, buyer arranges pick or pays shipping. Richard Six-one-Six 836-five one zero four

Strange Trans Yoke-New, Quick change for 904/Torqueflite - 125.00 MW Trans Yoke-Used PN-39040-B, for a 16 Spline G Force - 95.00 Headman Coated Dragster Up-sweeps, 2.250 tubes w/ 4" collectors - 450.00 Auto meter Brake Pressure Gauge PN-4426 2-5/8 Pro Comp Ultra Lite 0 to 2000 lbs - 45.00 Auto...

You have a PM

You have a PM

W8 Headers I think I have what your looking for. 1 set of Gebler, stainless Tri-Y headers for W8 heads. Originally on my 33 Dodge Roadster. Call my cell if your interested:616-836-5104 or email me [email protected] Thanks Jim Thurston

Looking for a used BSGL60 and a AABR55. Would like to find something usable that doen't need rebuilding. Thanks

If it's a standard deck? I have a Hogans sheet metal for 18deg. heads with single Dominator top that will work very well in your RPM range.

Denny, I have an SC 1000 on my car and work great and gives me a lot of information. One thing it does not have is a g-meter. I tried to call Todd at RacePac be he was at the PRI show. I will give him another call next week to see if I can use your box to get me there. Would you send me...

Vacuum Pump I have a 1 year old Start Sportsman 3 vane pump for sale like new. http://www.starvacuumpumps.com/viewPart.php?id=STR.04.01.000 Check it out. Jim Thurston 616-399-2069

W8 Headers I have just what your looking for. Gebler stainless, steped tri-y's. Give me a call after 6pm EST if your interested. Jim Thurston 616-399-2069

Speedy, after reading your post, you might want to invest in one of MSD's Firewall Feed-Thru. About $15.00 from Jegs. Even though it's a new wire you could still be losing voltage at the fire wall. The energy will take the path of least resistance and at higher RPM the cylinder preasure...

Coil Wire?? If the coil wire is the same age as the plugs wires, the first thing I would do is Ohm the coil wire because it get 8 time the use as the plug wires. MSD says 40 to 50 Ohms per foot.

Lenth How long is the driver shaft? I don't have the exact measurement but yet, but I will be needing on in the 40 to 41 inch range. Thanks' Jim Thurston

Drive shaft What's the measurements on the drive shaft? Thank Jim Thurston

You have a PM, Thanks

Bump to the front

For Sale Mark Williams aluminum 4" dia. driveshaft 35.5" long center of u joint to center of u joint $450.00 or would trade for a 3.5 or 4" dia. 40 to 41" long aluminum drive shaft. Also set of Gebler stainless steel tri-y headers for W-8 motor and strut car $600.00 call or email with any...

For Sale or trade a Precision Performance Kwik-Shift 1 "Power Shift" for a Proflite, with front cable and tranmission enter, Air shift With Safety Netural (P&N START) Precision Part No. 485 OR, Trade for a POWERGLIDE PUSH PATTERN, FRONT EXIT Precusion Part No. 463. Also for sale a set of...

Long shot here, but if you had a good set of 4:30 for that 12 bolt drop out, I would be interested in the gears. Thanks, Jim Thurston H: 616-738-7140 C: 616-836-5104