Toggle sidebar Toggle sidebar

Parts for sale

T

T-flow

Member
Jun 30, 2009
45
0
6
-Hogans sheet metal 2x4 4150 tee-pee top
15 degree wedge intake.
-Hogans sheet metal 15 degree wedge, no top.
-New Howards ultimate Billet rods, 5.850" sml. Journal.
-Several set of Jesel rocker arms. New and used. No stands.

Thanks, Todd
561-767-0630
 
T-flow said:
-Hogans sheet metal 2x4 4150 tee-pee top
15 degree wedge intake.
-Hogans sheet metal 15 degree wedge, no top.
-New Howards ultimate Billet rods, 5.850" sml. Journal.
-Several set of Jesel rocker arms. New and used. No stands.

Thanks, Todd
561-767-0630
Click to expand...
Todd,

Do you have any .180 offset intake in 1.7 ratio? Any 1.6 ratio exhaust? Any pairs on the shaft?

Thanks,

Keith
 
Last edited:
I will check for those codes. I will reply Friday with what I have.

Thanks, Todd @ T-Flow
 
Keith Rittenberry said:
Todd,

Do you have any .180 offset intake in 1.7 ratio? Any 1.6 ratio exhaust? Any pairs on the shaft?

Thanks,

Keith
Click to expand...

I'm not sure on .180" off set intakes. Most are going to be .550", 650", .700" off set. I might have some 1.6 ratio exhaust rockers, they would be on shafts with 1.7 intake ratio. I believe I have two full set's of rockers no stands. and some 1.8 ratio intake rockers. Maybe more.... a few boxes.
I will check.

Thanks, Todd @ T-Flow
 
T-flow said:
I'm not sure on .180" off set intakes. Most are going to be .550", 650", .700" off set. I might have some 1.6 ratio exhaust rockers, they would be on shafts with 1.7 intake ratio. I believe I have two full set's of rockers no stands. and some 1.8 ratio intake rockers. Maybe more.... a few boxes.
I will check.

Thanks, Todd @ T-Flow
Click to expand...
My mistake, Todd. The intake rockers I need are marked CZKR70 and CZKL70, and exhaust rockers marked CCAR 1.60 and CCAL 1.60.

Thanks,

Keith
 
Ok, one set- CZKR-1.70. AND CCAL-1.60
The other set dosent seem to have any makings on the rockers, just ratio.
I have pictures on my phone, so text me and I can send pictures out.

I also have a MSD crab distributor like new.

Thanks, Todd @ T-Flow
 
They are standard 18 degree port size. They fit raised runner 18,15, and some 12 degree heads.
Send me a text to 561-767-0630, I will send pictures.

Thanks, Todd
 
T-flow said:
-Hogans sheet metal 2x4 4150 tee-pee top
15 degree wedge intake.
-Hogans sheet metal 15 degree wedge, no top.
-New Howards ultimate Billet rods, 5.850" sml. Journal.
-Several set of Jesel rocker arms. New and used. No stands.

Thanks, Todd
561-767-0630
Click to expand...
what do you have for a 121 stand?? looking for 1.80 .650off/set
 
Keith Rittenberry said:
Todd,

Do you have any .180 offset intake in 1.7 ratio? Any 1.6 ratio exhaust? Any pairs on the shaft?

Thanks,

Keith
Click to expand...
Keith if you had a set of 1.80 c z k L1.80 fat body 121 stand's c z k r1.80 id trade them need lift S.t.d base limited .485'' lobe. I saw you asking Todd T Flow....there on my running motor or id would've sold them...
 
T-flow said:
-Hogans sheet metal 2x4 4150 tee-pee top
15 degree wedge intake.
-Hogans sheet metal 15 degree wedge, no top.
-New Howards ultimate Billet rods, 5.850" sml. Journal.
-Several set of Jesel rocker arms. New and used. No stands.

Thanks, Todd
561-767-0630
Click to expand...
Would you happen to have the hogan with no top 15 degree I know this is a old post but just checking
 
You must log in or register to reply here.
Top Bottom
Back